Simrad MN000802A-G Installationsanleitung

MN000802A-GNavico Marine Network Systems2 kW RadarInstallation Guide

GlobalMap 9300c HD GlobalMap 9200c GlobalMap 8300c HD GlobalMap 8200c GlobalMap Baja 840c GlobalMap 7300c HD GlobalMap 7200c Globalmap 5200c Global

The radar processor module connects to the various display heads using three different protocols. These are:- Ethernet. For more information on con

A radar unit should only be installed by a qualified marine technician, as potentially lethal high voltage is present along with heavy rotating part

4.1 Choose the scanner location The radar's ability to detect targets depends greatly on the position of its scanner. The ideal location for th

4.2 Power boat installations Normally, you should install the scanner horizontally, to produce an equal sweep around the power boat: However, w

4.3 Yacht installations Normally you should install the scanner horizontally, to produce an equal sweep around the yacht. However, a yacht heels ov

You can find the A-B line for any vessel as follows: • Using a drawing of the vessel, lay a rule along the line of the main deck and continue this

4.6 How to reduce false echoes and shadow zones False echoes can be produced on the radar display if the scanner is installed too close to an object

4.8 Install a scanner on a trestle Depending on your chosen location for the scanner, it may be easier to install the scanner if you fabricate a tre

NOTE: Use the bolts supplied as these are hardened stainless steel and the correct length. 4.10 Install the radar processor Install the radar pr

2 kW Radar Installation Manual | 1 1.1 FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital

The Navico 2 kW radar system consists of a scanner, a radar processor, and associated cables. some of which need to be ordered separately There are

1 Packing list LA000450 1 Installation sheet MTZ303386 LA000410 1 Mounting template LA000451 AA010012 2 kW Radar processor standard components

AA010089 Optional longer length interconnection cable for radar scanner - order separately Quantity Item Part name Part No 1 Interconnection cab

Most installation problems are caused by shortcuts taken with system cables. When wiring the radar: • DON'T make sharp bends in the cables. •

Carefully lift the main unit and stand it upright in the slot on the scanner casing:

Remove the shield cover from the underside of the main unit to expose the connector locations and ground terminal location. The broken line shows t

Place the internal locking nut over the end of the interconnection cable, then attach connectors B and C to the connectors (as shown in the figure)

9 Yellow #24 1 10 White (big) #12 3 Shell Braid shield X 6.2 Run the 2 kW interconnection cable (NS003100/NS003101) to the radar process

6.3 2 kW radar processor connections There are four interface connectors on the rear of the 2 kW radar processor, plus a Chassis Earth. You can conn

6.4 Connect the power cable The power cable to the radar processor is NOT supplied. Power must be supplied through a fuse/breaker element located at

2 | 2 kW Radar Installation Manual 1.5 Warranty The Navico Warranty Statement is supplied as a separate document. It is shipped with the Product

6.5 Connect the ground wire The radar processor has a Chassis Earth connection stud located on the far right hand side of the unit. The Chassis Eart

Both the Simrad GB40 and the Northstar 8000i systems interface to the Navico radar via a ethernet network. The Ethernet network connectivity is the

NS004815 Optional parts to connect (GB40 only) AA010151 AT10-HD This is used to supply the radar processor with heading information at 10 hz fro

7.2 Simrad GB40 connection using SimNet heading The diagram below details how to connect the Navico radar to a GB40 system using a crossover cable (

7.3 Northstar 8000i / Simrad GB 40 using NMEA 0183 heading The diagram below shows how to connect the radar to a Northstar 8000i or Simrad GB40 syst

C AA010012 2 Kw Radar processor box. No cables supplied. Connects to GB40 system via Ethernet. The Radar box requires heading @10hz. For Vessels

I 1 Northstar 8000i or Simrad GB40 NavComputer Master I* 1 Northstar 8000i or Simrad GB40 second station The compass must be NMEA compliant and c

The radar transmits until you change the radar mode to Standby or Off. ¾ Set Radar Range offset (trigger Delay) The radar sweep should commence at

(Small Distance Units) 4m/13.12 ft Sets the antenna height above the water-line so that the sea clutter control works properly Radar Open Array P

8.1 Parts needed If you're connecting the radar to an Simrad NX40/NX45 or a Northstar M841 or M121 you need the AA002461 connection kit. This i

Contents 1 2 kW Radar Installation Manual 1 1.1 FCC Statement...

8.2 Connect the 2 kW radar processor to an M84 or M121 Display A AA010024(SIM or NOR) 2 kW Scanner comes with 15 m (49 ft) cable (B) Attached NS00

8.3 Set up the radar with the Northstar M84 or M121 When the radar is enabled, it will turn on, warm up, and enter standby mode. ¾ To enable the r

• Adjust the gain setting if necessary, so that a reasonably good image of the jetty echo is displayed on the radar window. At this stage, the jett

9.1 Parts needed to connct to a Northstar 6000i / 6100i NS003107 cable for 6000i and 6100i installations only - supplied with 6000i and 6100i syste

9.2 Connect the 2 kW radar processor to a 6000i or 6100i display The following diagram shows the recommended method for connecting a radar processor

F Circuit breaker/fuse box G Optional radar communications extension cable (NS003108) H Vessel's Ground I NTSC Video Input J Fuse (7A) K GPS

9.3 Connect the radar communications cable (NS003107) to the junction box The radar communications cable (NS003107) splits the 14 pin connector of t

NMEA devices must be connected to an unused NMEA port on the connector strip. The remote power signal configuration is explained in "Configur

* See cautions above. ** See cautions above. The end view of the (three) 3 connectors are shown: 6000i/6100 connector NMEA pin assignments Conne

9.4 Configure the remote power control for a 6000i or 6100i (common power source) There is a choice of two different modes for powering the radar ON

8 Connect Simrad NX40 / NX45, Northstar M84 / M121 38 8.1 Parts needed...

9.6 Set up the radar with the Northstar 6000i or 6100i 9.7 Turn the radar on and off 1.1.1 Before you turn on the radar for the first time To exten

9.8 Configure the navigator communications IMPORTANT: If you are going to operate the radar without a heading sensor, ignore this section and set u

9.10 Heading sensor requirements The heading sensor can be a stand-alone unit or may be integrated into an auto-pilot system, provided that it suppl

• Press Return. 9.14 Tune the radar The Navico radar uses a fully automatic tuning procedure that continuously checks for optimum adjustment durin

• Press Gain, then press 1, 5, 0 to set the gain to 150. If you're using standard screen colors, the display will show a green ring with a b

9.18 Set the heading calibration (heading sensor not installed) The heading calibration rotates the radar image on the screen so that a target dead

9.21 Manual tuning procedure for the 6000i or 6100i system Note: The following manual tuning procedure is provided only for possible situations whe

10.1 Parts needed to connect to Lowrance displays RIM300 Radar Interface Module Quantity Item Part name Part No 1 Rim 300 Cable Heading Senso

Simnet cable joiner 44172260 Lorance NMEA 2000 "T" Connector 037-0491-01 10.2 RIM300 RIM 300 Installation The RIM 300 will replace t

• If you are powering a NMEA 2000 network or an LGC-3000 GPS antenna, you must connect the NMEA 2000 power cable. Attach the NMEA 2000 red wire (+

12.2 Radar is not operating correctly...66 12.3 If the scanner fails to

10.4 Setup the basics • After turning on the unit, press MENU|MENU, then use ↑ ↓ to SYSTEM SETUP and press ENT. Communications Port selected

Radar Setup selected from Radar menu (left). Radar Setup menu with Full Color on Black highlighted (right). • Highlight HEADING UP and press EN

• That will launch the Anti-Rain Clutter vertical scrollbar. Press ↓ until the Anti-Rain Clutter is set to zero percent. Press EXIT. (Notice the co

Increase Trigger Delay to diminish the size of the red ring (left). To set Trigger Delay correctly, reduce the ring to as small a size as possibl

Main Bang Suppression begins with the same red ring we resized during Trigger Delay setup (left). Slowly increase Main Bang Suppression to make t

Before doing any maintenance work, always ensure that the radar system is turned OFF at the main power source. If a rectifier unit is used, turn

• Remove any dust, dirt, or sea salt from the external surfaces, particularly the front side of the scanner, with a lint-free cloth dampened with

This appendix gives information on fixing possible problems with the radar. Many problems are caused by: • faulty or loose contacts at switches and

7 Check the motor and replace any faulty component. (See the Service Manual for information on replacing the motor) 8 Check the wiring of the inte

12.7 Confirm the equipment installed 1. Confirm the type of navigator used with the radar (6000i, etc). MAKE MODEL SERIAL NUMBER SOFTWARE VERS

This manual explains how to install the Navico Radar scanner and the radar processor System. It Explains how to connect to products produced by Navi

2 kW scanner DC input 10.8 V to 15.6 V DC (DC 12 V system ONLY) Scanner type Radome Scanner model NS004790 Scanner dimensions Depth: 17.7&quo

2 kW Radar processor specifications Radar system NS-RDR-1021MD Processor model NS004780 Processor dimensions Width 5.6" (142 mm) Height 2.2

The microwave energy radiated by a radar antenna is harmful to humans, especially to the eyes. NEVER look directly into an open waveguide or into th

The Navico radar system platform is designed to work with many types and models of display heads that belong to brands under the Navico house of bra