Simrad PI DEPTH Spezifikationen Seite 128
- Seite / 268
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Simrad PI32
116
857-164636 / Rev.A
Sensor configuration
On delivery, all Height sensors are configured in Channel 14
and with Fast update r ate.
Note: The sensor and the PI32 system setup must correspond,
otherwise the communication will not work.
To change the sensor setup (channel selection), use the PI
Configurator utility.
The sensor update rate controls how often the sensor reads and
reports the height. T hree settings are available. Note that a faster
update rate will decrease the battery life.
• Fast (~5,5 sec): Recommended for new trawl or changes in
rigging to monitor any instabilities or unexpected changes.
This mode provides the shortest battery life before charging.
• Normal (~14 sec): Recommended for well known trawl
behavior with stable situations. Use this setting during
normal conditions.
• Slow (~34 sec): Recommended to monitoring a stable
situation over time. The system will be more sensitive to bad
communication conditions due to the slow data update. This
mode provides longest operational battery life before
charging.
System configuration
Sensor configuration: The sensor must be configured with a
unique sensor number. Select channel number and update rate
according to the sensor’s configuration. Write down the
configuration for future reference.
Status & Receiver: The Interference filter must be switched on.
Set it to level 9 if you have noise problems from other
hydroacoustic sources. Note t hat with the filter on, it will
influence the signal spectrum shown in the St atus display.
Sensor filter: Switch this f ilter to Light. Set it to Heavy only if
you experience excessive noise. Position Off will provide raw
data and fastest possible response.
- Operator manual 1
- Catch monitoring system 3
- About this document 4
- Sections 5
- 12 Sensor test procedures 6
- 13 Technical specifications 6
- Simrad PI32 10
- INTRODUCTION 13
- SYSTEM DESCRIPTION 14
- System diagram 15
- Operator Unit 16
- Sensor overview 18
- Battery chargers 19
- GETTING STARTED 20
- Power on 21
- Power off 21
- Page 1: Echo sounder 22
- Page 2: Numeric display 22
- Page 3: Graphic display 22
- Page 4: Navigation display 22
- Leafing through the pages 23
- Other display presentations 23
- Introduction to the main menu 24
- Introduction to the keypad 25
- Introducing the sensors 27
- Depth: How deep can you go? 29
- Rip: Check for damages! 30
- APPLICATION EXAMPLES 32
- Purse seine 33
- Danish seine 34
- Bottom trawl 35
- Pelagic trawl 36
- Echo sounder 37
- Graphic display 38
- DISPLAY PRESENTATIONS 39
- Numeric display 40
- Depth presentation 43
- Height presentation 44
- Spread presentation 45
- Surface temperature 49
- Status display 50
- → Receiver setup, page 174 51
- Echo sounder display 52
- Bottom expansion 53
- Navigation display 55
- Position display 56
- OPERATIONAL PROCEDURES 57
- → Numeric display, page 28 59
- How to set up the sensors 60
- Predefined settings 61
- How to use the sensors 64
- How to test the sensors 66
- How to define sensor offsets 68
- MENU Exit 72
- GAIN- GAIN+ 72
- (CD11105C) 72
- → Twin Spread, page 128 73
- → Trawl info, page 182 73
- Howtoviewechosounderdata 75
- How to set up marker lines 76
- Depth and Height marker lines 77
- Spread marker line 77
- → Graphic setup, page 160 78
- Access to the parameters 80
- Set up the parameters 80
- Ping to ping filter 82
- Colour threshold 82
- Signal threshold 82
- Depth grid 82
- Standard mode 84
- Phased range mode 84
- Activate A-Scope 88
- De-activate A-Scope 88
- How to define alarm limits 89
- Surface temperature alarm 90
- Clearance alarms 90
- How to select menu language 92
- → Page setup, page 171 93
- PRACTICAL USE OF THE SENSORS 95
- PI Bottom Contact sensor 99
- Bottom Contact presentatio n 100
- Sensor configuration 100
- System configuration 101
- Mounting 101
- 857-164636 / Rev.A 102
- PS Bottom Contact sensor 103
- PI Catch sensor 107
- Presentation 108
- PS Catch sensor 112
- Catch presentation 113
- PI Depth sensor 116
- Numerical presentation 117
- PS Depth sensor 121
- PI Height sensor 126
- Daily operation 127
- PI Rip sensor 130
- Numeric presentation 131
- PI Spread and Remote sensors 135
- Installation principle 138
- Sacrificial water switch 139
- PI Twin Spread 140
- Main parts 141
- PI Temperature sensor 145
- Temperature presentation 147
- PS Temperature sensor 151
- SENSOR CHARGERS 156
- PI Charger 157
- PS30 Charger 159
- General guidelines 160
- Battery depleted frequently 160
- Typical sensor (PI Depth) 160
- MENU SYSTEM 161
- The main menu 162
- Menu system 163
- REFERENCES 164
- Depth calibration 165
- Echo presentation setup 166
- Echo sounder setup 169
- Related topics 170
- Factory presets 171
- Graphic setup 172
- → Sensor setup, page 179 173
- → Numeric setup, page 169 173
- Interface setup NMEA 174
- Applicable telegram formats 177
- Interface setup remote/alarm 179
- Navigation setup 180
- Numeric setup 181
- Offset adjust 182
- Page setup 183
- Palette setup 184
- Position display setup 185
- Receiver setup 186
- Sensor alarms 189
- Sensor setup 191
- Speed setup 192
- Surface temperature setup 193
- Trawl info setup 194
- Units setup 195
- PI CONFIGURATOR 196
- Basic information 197
- Available equipment 198
- About sensor configuration 199
- Changing the update rate 200
- Main dialogue description 201
- Operational procedures 203
- Software installation 204
- How to interface the sensor 205
- References 210
- Communication P o rt Setup 212
- Operation 212
- Configure Sensor 213
- Factory Default 216
- Language 218
- LED Control 219
- Message field 220
- PI Configurator 221
- Ping control 222
- Read Sensor Data 224
- Sensor Type 226
- Show Channel At Startup 228
- Examples 229
- Terminate Communication 230
- Maintenance 231
- Making a programming cable 233
- Troubleshooting 234
- SENSOR TEST PROCEDURES 235
- Bottom Contact test procedure 236
- Testing on land 237
- Testing in water 237
- Catch sensor, test procedure 239
- Depth sensor, test procedure 242
- PI32 Calibration procedure 244
- PI44 Calibration procedure 244
- Height sensor, test procedure 245
- Tools and equipment required 248
- TECHNICAL SPECIFICATIONS 255
- PI Bottom Contact 256
- PI Catch & PI Rip 256
- PI Depth 257
- PI Height 258
- PI Spread & Remote 258
- PI Temperature 259
- - To 70% capacity: 1 hour 260
- - To 100% capacity: 4 hours 260
- - To 100% capacity: 16 hours 260
- E 2005 Simrad AS 268
- ISBN 82-8066-059-3 268
Verwandte Produkte und Handbücher für Nein Simrad PI DEPTH
Nein Simrad FS25 Betriebsanweisung
(108 Seiten)
(108 Seiten)
Nein Simrad SP60 - REV D Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Nein Simrad ER60 - REV B Technical Information
(256 Seiten)
(256 Seiten)
Nein Simrad SH90 - REV B Spezifikationen
(2 Seiten)
(2 Seiten)
Nein Simrad PI HBU - REV A Bedienerhandbuch
(12 Seiten)
(12 Seiten)
Nein Simrad SH80 - REV C Installationshandbuch
(214 Seiten)
(214 Seiten)
Nein Simrad ITI Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Nein Simrad SP60 - REV D Installationshandbuch
(178 Seiten)
(178 Seiten)
Nein Simrad EQ 55 Technical Information
(154 Seiten)
(154 Seiten)
Nein Simrad SH80 - REV C Installationshandbuch
(200 Seiten)
(200 Seiten)
Nein Simrad RS90 Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Quantum DAT 24 Drive manuels
Manuels d'utilisation et guides de l'utilisateur pour Lecteurs de bandes magnétiques Quantum DAT 24 Drive.
Nous fournissons des manuels en pdf 1 Quantum DAT 24 Drive à télécharger gratuitement par type de document : Guide de l'utilisateur
Quantum DAT 24 Drive Guide de l'utilisateur (181 pages)
marque: Quantum | Catégorie: Tape drives | Taille: 0.49 MB |
Table des matières
Contents
5
Introduction
13
Figure 2-1
20
Figure 2-2
20
Figure 2-4
24
Data Phase
27
Status Phase
27
Commands
46
Conventions
47
ERASE (19h)
49
LOCATE (2Bh)
59
Page Header
73
MODE SENSE (1Ah)
101
Mode Page Format
105
READ (08h)
117
REWIND (01h)
161
SEEK BLOCK (0Ch)
162
SPACE (11h)
166
VERIFY (13h)
172
WRITE (0Ah)
174
Plus de produits et de manuels pour Lecteurs de bandes magnétiques Quantum
| Modèles | Type de document |
|---|---|
| DLT-V4 |
Manuel de l'utilisateur
Quantum DLT-V4 User's Manual,
97 pages
|
| SDLT 320 |
Manuel de l'utilisateur
Quantum SDLT 320 User's Manual,
150 pages
|
| DLT2700xt |
Manuel de l'utilisateur
Quantum DLT2700xt User's Manual [en] ,
345 pages
|
| L500 |
Guide de l'utilisateur
Quantum L500 User's Guide,
120 pages
|
| DLT4500 |
Manuel de l'utilisateur
Quantum DLT4500 User's Manual,
360 pages
|
| DLT-V4 |
Manuel de l'utilisateur
Quantum DLT-V4 User's Manual,
62 pages
|
| DAT160 Drive |
Guide d'installation
Quantum DAT160 Drive Installation Guide,
2 pages
|
| DAT 432/864 Loader |
Guide de l'utilisateur
Quantum DAT 432/864 Loader User's Guide,
59 pages
|
| PX720 |
Manuel de l'utilisateur
Quantum PX720 User's Manual,
2 pages
|
| ACL 2640 |
Guide du propriétaire
Quantum ACL 2640 Operator's Guide,
68 pages
|
| Travan 20 SCSI |
Manuel de l'utilisateur
Quantum Travan 20 SCSI User's Manual,
70 pages
|
| Scalar i6000 |
Guide de l'utilisateur
Quantum Scalar i6000 User's Guide,
106 pages
|
| TC-L33CX-EY-B |
Fiche technique
Quantum LTO-3HH,
2 pages
|
| TC-L32AX-EY |
Fiche technique
Quantum LTO-3 HH tape drive TC-L32AX-BR,
2 pages
|
| TC-L32BX-EY |
Guide de l'utilisateur
Quantum TC-L32BX-EY tape drive,
109 pages
|
| TC-L53FN-AR |
Guide de l'utilisateur
Quantum TC-L53FN-AR tape drive,
96 pages
|
| DLT-V4 |
Manuel
   
Quantum DLT-V4,
28 pages
|
| Sun StorEdge L100 |
Spécifications
Quantum Sun StorEdge L100 Specifications,
42 pages
|
| DLT 7 |
Manuel
Quantum DLT 7 Product manual,
177 pages
|
| DLT 8000 |
Manuel
Quantum DLT 8000 Product manual [es] ,
408 pages
|
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern