Simrad NSS Installationsanleitung Seite 33
- Seite / 66
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
|
33
NMEA2000 / SimNet | NSS Installation Manual
NMEA2000 / SimNet
NMEA 2000 is a combined electrical and data speci cation.
NMEA2000 and SimNet is a data network based on CAN (Control Area Network) bus technol-
ogy that makes interconnection and integration of Simrad and other NMEA2000 products
simple. NMEA2000 permits exchange of data and commands between the interfaced
products. The data transfer capacity of SimNet is 50 times higher than that of the NMEA0183
standard at 4800 baud.
Certain NMEA0183 data can be converted to and from the SimNet network by;
• using the NSS display to bridge data (internally).
• using an optional external converter unit such as the Simrad AT10.
• using a third-party NMEA2000 to NMEA0183 bridge.
Most NMEA2000 devices can be connected directly to a SimNet backbone and SimNet
devices can be connected to a NMEA2000 network by using adapter cables. (see ‘Simnet
Cables’ on page 60)
Note: The NSS has a Micro-C NMEA2000 connector and is fully compatible to work in a
SimNet network.
SimNet: The basics
• SimNet is Simrad’s proprietary network based on NMEA2000 CAN bus (SAE J1939 protocol).
• SimNet is a powered network. It must have a separate 12-15 V DC power supply protected by
a 5 Amp fuse. Do not connect the SimNet power cable to the same terminals as the start bat-
teries, Autopilot Computer, Radar, thruster or other high current products.
• A SimNet network consists of a linear “backbone” from which “drop cables” to SimNet devices
connect. Devices that have more than one SimNet connector can be part of a SimNet
backbone (daisy chained) (But not as part of a NMEA2000 backbone).
• A drop cable is a SimNet cable that connects a SimNet device to the backbone. A drop cable
has a maximum length of 6 m (20 ft).
• A SimNet Network has a maximum cable length of 120 m (394 ft), which includes drop cables
+ 30 m (98.5 ft) mast cable. Total 150 m (500 ft) max.
• A SimNet network needs to have a terminator at each end of the backbone. A terminator can
be one of the following:
• a power cable with built in terminator (red cap)
• a terminator plug (red cap)
• terminated in-line joiner (red locking collars)
• a wind transducer (terminator is in the mast head unit as opposed to mast cable).
• Certain Simrad products have two SimNet connectors, which can be made to be part of
the backbone. Connecting from device to device is known as ‘daisy chaining’ This network
topology is not o cially NMEA 2000 compliant.
MenuMenu
• NMEA2000 devices can be connected to the SimNet Network providing they:
• are NMEA2000 certi ed
• meet the CE, FCC regulations with a SimNet adapter cable
• do not exceed the SimNet load speci cation (please refer to separate document
Simrad SimNet Installation Manual (20222006)
10
- Installation Guide 1
- NSS Installation Manual 2
- Copyright 3
- Warranty 3
- Declarations and conformance 3
- Compliance Statements 3
- About this manual 4
- Contents 5
- NSS overview 7
- Front - Controls 8
- Rear - Connectors 9
- NSS7 or NSS8 10
- NSS12 NSS12 11
- Planning the installation 12
- Check the contents 13
- Mounting location 14
- Mounting the NSS display 15
- Bracket mount 16
- Wiring the NSS 17
- Connecting power 18
- Power Control setup 19
- External alarm 20
- External Alarm Setup 20
- Echosounder 22
- Transducer adapter cables 23
- Echosounder software version 24
- T r ansducer type 25
- SimNet Network 26
- HD radar 27
- Scanner type 28
- Software version 28
- Serial Number 28
- MARPA status 28
- Reset device ID 28
- Sidelobe suppression 29
- Video In 30
- NMEA0183 31
- Serial port setup 32
- NMEA2000 / SimNet 33
- Mico-C to SimNet 34
- SimNet power 34
- SimNet terminator 34
- SimNet backbone 35
- SimNet drop cable 35
- SimNet power cable 36
- SimNet Terminator 36
- Ethernet to SimNet: 37
- NMEA 2000 / SimNet setup 38
- Ethernet (NETWORK port) 39
- Transducer 40
- Broadband Radar 40
- Databases 41
- IP addresses 41
- Module network light 41
- Autopilot 42
- Using the SG05 EVC gateway 43
- Autopilot setup 43
- Dockside setup 44
- Drive voltage 45
- Drive engage 45
- Motor output 45
- Rudder deadband 45
- STBY/AUTO key 45
- Compass calibration 46
- Compass mounting o set 46
- LUBBER LINE 46
- Autotuning 47
- Seastate lter 47
- Navigation change limit 50
- CZone connection to SimNet 51
- CZone setup 52
- Applying Software Updates 53
- Dimensioned Drawings 55
- 12 mm (0.47") 56
- 2.3 mm (0.09") 56
- 41 mm (1.61" 56
- 41 mm (1.61") 56
- Connector Pinouts 58
- NMEA2000 59
- Network (Ethernet) 59
- Accessory cables 60
- Supported data 61
- NMEA2000 PGN (transmit) 63
- NMEA0183 supported sentences 64
- Speci cations 65
- *988-10107-001* 66
Verwandte Produkte und Handbücher für Navigatoren Simrad NSS
Navigatoren Simrad AP28 Technical Information
(124 Seiten)
(124 Seiten)
Navigatoren Simrad NSS Installationsanleitung
(23 Seiten)
(23 Seiten)
Navigatoren Simrad CX54-DE Betreibershandbuch
(118 Seiten)
(118 Seiten)
Navigatoren Simrad HH36 Bedienungsanleitung
(88 Seiten)
(88 Seiten)
Navigatoren Simrad HH36 Bedienungsanleitung
(88 Seiten)
(88 Seiten)
Navigatoren Simrad NSS7 Installationshandbuch
(96 Seiten)
(96 Seiten)
Navigatoren Simrad AC42 Technical Information
(116 Seiten)
(116 Seiten)
Navigatoren Simrad AP26 Bedienungsanleitung
(148 Seiten)
Navigatoren Simrad MX525A Spezifikationen
(34 Seiten)
(34 Seiten)
Navigatoren Simrad RS12 VHF Betriebsanweisung
(72 Seiten)
(72 Seiten)
Navigatoren Simrad MX525A Spezifikationen
(34 Seiten)
(34 Seiten)
Navigatoren Simrad AP50 Spezifikationen
(62 Seiten)
(62 Seiten)
Dimplex DS3311 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Kuchenki Dimplex DS3311.
Dostarczamy 2 pdf podręczników Dimplex DS3311 do pobrania za darmo według typów dokumentów: Instrukcja Właściciela, Instrukcja Obsługi
Kommentare zu diesen Handbüchern