Simrad AP28 Technical Information PDF herunterladen (Seite 106)

104 | Troubleshooting

5.3 Resets

Autopilot reset

An Autopilot Reset is part of the final test at the factory,

which will reset the memories to factory settings. Unless

you need to clear all stored values during the installation

setup, you should not perform an Autopilot reset.

To confirm the autopilot reset press the

softkey.

The Installation and Setup procedures must be

repeated after a reset has been performed!

In the event an Autopilot reset has been made, refer to

chapter 3.2.

Global reset

A Global reset resets the entire SimNet setup in the

Simrad Group and initiates a new automatic interface

setup. See chapter 3.1.

1 2 ... 101 102 103 104 105 106 107 108 109 110 111 ... 123 124

Operator manual 1
About this manual 4
AP28 Manual 5
4 6
1 Operation 7
Softkeys 9
Symbols 9
1.2 ON/OFF 10
1.3 Backlighting 11
1.4 Standby mode 12
Follow-Up steering (FU) 13
1.5 Automatic steering 14
Heading capture 15
14 16
Response adjust 17
16 18
1-9 1 4 18
Operation 19
1-9 1 4 19
18 20
Operation 21
22 24
Main course 25
Course change 40° 25
Initial course change 20° 25
Leg distance 25
Operation 27
Operation 29
28 30
1.6 NoDrift mode 32
1.7 Navigating with the AP28 33
32 34
Operation 35
34 36
Operation 37
36 38
Tacking in Wind mode 39
38 40
(sailboats) 41
Operating in WIND 42
Operation 43
Figure 1-2 43
42 44
1.11 Multiple station system 45
2 Main menu 47
2.1 Data pages setup 48
Disabling pages 49
Enabling pages 49
2.2 Trip log 50
2.3 User setup menu 50
Damping 51
Sources 53
52 54
Main menu 55
Display 56
Language 57
Units of measure 58
Seastate filter 59
Sailing 60
Main menu 61
Range Default 61
Auto – Apparent - True Auto 61
Off - On Off 61
2.4 Remote lock 62
Main menu 63
3 Setup at installation 65
3.2 Installation Menu 66
Commissioning 67
66 68
(Not applicable for EVC) 68
Setup at installation 69
68 70
(Not applicable for EVC) 70
Setup at installation 71
Setup at installation 73
72 74
-10 - +10 0 – ±5: 0.1 74
5 – 10: 0.5 74
0.0 m, ft 74
15 - 90 1 30 ° 75
Setup at installation 75
Range Change per step 75
Default Units 75
74 76
10 - 30 10 10 ° 76
Setup at installation 77
(Not applicable for 77
>3 sec 78
Setup at installation 79
78 80
Setup at installation 81
Turn rate too high 81
Turn rate too low 81
80 82
Setup at installation 83
82 84
-180 - +180 1 0 ° 84
Setup at installation 85
0.50 – 1.50 0.01 1.00 85
84 86
OFF - 30 1 6 knots 86
Setup at installation 87
Automatic steering 88
88 90
Setup at installation 91
Final seatrial 92
Providing user training 93
Calibration 94
Rudder drive 94
Setup at installation 95
SimNet configuration 96
3.3 Service Information 98
Setup at installation 99
98 100
4 Alarm system 101
4.2 Acknowledging an alarm 102
4.3 Viewing active alarms 102
4.4 Alarm codes 102
Blank page 104
5 Troubleshooting 105
5.3 Resets 106
5.4 Alarms 107
6 Maintenance 111
6.5 Compass 112
6.6 Drive unit 112
7 Optional equipment 113
7.3 JS10 Joystick (NFU) 114
Zero point setting 115
8 Glossary 117
116 118
Glossary 119
9 Index 121

Kommentare zu diesen Handbüchern

Keine Kommentare

Simrad AP28 Technical Information Seite 106

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Navigatoren Simrad AP28