Simrad SP270 Installationshandbuch Seite 78
- Seite / 254
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Simrad SP270
34
851-160572 / B
1 Set the switch S101 at the rear panel on the Sonar Control
Unit to OFF position. For location of the switch, refer to
figure 14.
2 Disconnect all connections to the rear panel on the Sonar
Control Unit.
3 Use the 3mm Allen key to unscrew the four screws on the
front of the operator panel, and pull the electronic drawer
carefully out. Note the two cables to the display on the top
of the drawer unit.
4 Disconnect the two display cable plugs on the drawer unit,
and dismount the top cover of the drawer.
5 Locate the DIL switch S2 (refer to figure 20), and set the
switches according to the table below.
6 If the output voltage is only half-wave rectified, refer to
figure 20, and set the links LK19 LK20 and LK21 to
position A.
Gyro
DILswitchS2
1 2 3 4 5 6 7 8
Synchro 1:360
+REF On Off Off Off Off Off Off Off
-- R E F On On Off Off Off Off Off Off
1:180
+REF On Off Off On Off Off Off Off
-- R E F On On Off On Off Off Off Off
1:90
+REF On Off Off Off On Off Off Off
-- R E F On On Off Off On Off Off Off
1:36
+REF On Off Off On On Off Off Off
-- R E F On On Off On On Off Off Off
7Donotinsert the Control Unit drawer until mentioned in a
later chapter.
Course gyro with serial line output
The Sonar Control Unit can read the course gyro data (and/or
the speed log data) from a serial line with on of the following
outputs (tick off for the type which will be connected):
• RS-232 Serial line
• RS-422 Serial line
• 20 mA current loop
The format of the serial line data is standard NMEA 0183, and
the telegram can contain both the course and speed data (refer to
the telegram format in the end of this chapter).
- Installation manual 1
- Simrad SP270 3
- Fishery sonar 3
- Sections 5
- References 6
- The reader 6
- High voltage safety warning 9
- Artificial respiration 10
- Combining ECM and artificial 10
- Do you know what to do? 10
- Introduction 11
- Document revisions 12
- About this document 12
- Table of contents 13
- Blank page 14
- Installation document 15
- Overview 15
- 851-160571 / B 16
- Installation procedures 18
- Auxiliary equipment 19
- Supply conditions 20
- General safety rules 21
- Installation requirements 22
- Dry docking 23
- Equipment handling 24
- Initial preservation 25
- Inspection and unpacking 27
- After use storage 30
- Re-packing 32
- ESD precautions 32
- Temperature protection 33
- Technical specifications 34
- Installation planning 45
- Sonar room requirements 46
- 851-160572 / B 48
- Mounting the trunk 49
- Protecting blister 50
- Corrosion protection 50
- Installation of the hull unit 53
- Alignment of the transducer 54
- Installation checklist 55
- Desk top mounting 61
- Panel mounting 62
- Bulkhead mounting 63
- Cable plan 64
- Sonar Control Unit cabling 66
- Transceiver Unit cabling 67
- Hull Unit cabling 70
- Connecting the course gyro 71
- Connecting the speed log 81
- Connecting a pulse log 81
- S0J 30.06 88
- . . . . . . . . . . . 89
- DQG;ument 90
- PREPARI 91
- Starting 92
- Starting up the Hull Unit 94
- Hand crank 95
- (CD3125) 95
- The motor control unit 95
- STOP position 96
- 380/440V: 2 96
- 380/440V 99
- (CD3127) 99
- Mains connection to the motor 99
- , must then be 100
- Start-up procedures 101
- Middle position switch 101
- 160573/A 101
- Connect the SONAR 102
- , adjust the picture with 103
- ~~'. 104
- Press the CIRCLE 105
- , and press the 105
- TRACK button, (9) and check 106
- Checking the bridge functions 107
- Press the LOWER button for 108
- , and check if the 109
- UPPER is shown in the 110
- (refer to figure 111
- Sonar Control Unit in the 111
- RCG. . . . . 112
- Connecting the transducer 113
- Simrad SP 270 114
- , and check 115
- S8RAD $lIMA!) 116
- J~Gp.rsor to TX 117
- PP FILTER to 118
- ILIARY E 119
- Sonar Control Unit by 120
- , set the speed to 121
- , switch off the 121
- Be aware 122
- , and check that the 123
- Source level 124
- Auxiliary 125
- Ext. trig 125
- 0 Vert. input 125
- Approx. 5 125
- Serial No 126
- , depth and 127
- Measurements/calculations 127
- SL OMNI dB/ /~Pa 128
- Receiving. 129
- Value Unit 130
- Noise/spee 131
- , make the test 132
- ' hull 133
- BEARING WITH 134
- STABLE SPEED 134
- -- - - -- - - 134
- LLAT..IO,Ni; 135
- Installation remarks 135
- Drawings 137
- (;lCUment revisions 138
- Original issue 140
- 851- 160675 / AA000 / 4- 11 147
- Document history 150
- &RQQHFWLQJ WKH 233
- 6LPUDG ,7 233
- 7UDZO ,QVWUXPHQWDWLRQ 6\VWHP 233
- 'RFXPHQW UHYLVLRQV 234
- &RQWHQWV 235
- 'RFXPHQW KLVWRU\ 236
- $ 237
- E 2004 Simrad AS 252
- ISBN 82-8066-014-3 252
Verwandte Produkte und Handbücher für Nein Simrad SP270
Nein Simrad 38-9 - REV B Installationshandbuch
(202 Seiten)
(202 Seiten)
Nein Simrad SH90 - REV B Spezifikationen
(44 Seiten)
(44 Seiten)
Nein Simrad 50-200 COMBI C - REV D Bedienerhandbuch
(112 Seiten)
(112 Seiten)
Nein Simrad AP26 Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Nein Simrad FS25 Bedienungsanleitung
(8 Seiten)
Nein Simrad 38-7 - REV C Bedienungsanleitung
(25 Seiten)
(25 Seiten)
Nein Simrad TP22 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Nein Simrad SX90 - REV B Installationshandbuch
(78 Seiten)
(78 Seiten)
Nein Simrad HH33E Bedienungsanleitung
(79 Seiten)
(79 Seiten)
Nein Simrad AP27 Bedienerhandbuch
(38 Seiten)
(38 Seiten)
Nein Simrad TP22 Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Nein Simrad SP70 - REV D Spezifikationen
(25 Seiten)
(25 Seiten)
Nein Simrad CX54-DE Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Nein Simrad AC42 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Nein Simrad AP50 Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Nein Simrad RT62 Bedienungsanleitung
(36 Seiten)
(36 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern